Teejet GuideLine SmartPad II Instrukcja Użytkownika Strona 110
- Strona / 198
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
3-56 Chapter 3 - Real-Time Guidance
The Circle Pivot Guidance Mode
SmartPad II
Software Version 4.02
Marking Point B
Once point A is marked the operator should drive along the pivot circle until they feel they have described the circle
as well as possible. The Mark A button has changed to Mark B button, see Figure 3-76. The Swath software will not
allow the user to mark point B with in 12 seconds of marking point A. After 12 seconds, the Mark B button becomes
active and the operator can mark point B anytime after.
Circle Guideline Guidance
Once the operator has marked point B, the circle guideline will appear in the SmartPad display and the lightbar will
begin providing guidance instructions. It is not necessary to drive the entire circumference of the center pivot in order
to initiate guidance. As shown in this example, the operator drove only a portion of the circumference marking points
A and B, and then used the guideline to continue driving the remainder of the circle, see Figure 3-77.
Figure 3-75: Marking Point A
Figure 3-76: Preparing to Mark Point B
- USER GUIDE 1
- Copyrights 2
- Trademarks 2
- Limitation of Liability 2
- Table of Contents 3
- Chapter 1 - Introduction 9
- Welcome to SmartPad II 10
- What’s New in Version 4.02 12
- Figure 1-1: 13
- Unpacking Your System 14
- Installing Your System 14
- GPS Receiver 14
- GPS Antenna 15
- Lightbar 15
- Lightbar 17
- Interface Cable 17
- GPS Receiver Compatibility 17
- Chapter 1 Notes 22
- Chapter 2 - Software Overview 23
- SmartPad II Software Overview 24
- SmartPad II Keys 25
- Screen Selection 26
- Data Entry 26
- Menu Pages 26
- Dialog Boxes 27
- First Time Setup Process 29
- SmartPad II Main Launcher 30
- Launching an Application 31
- Main Setup 32
- Communications Setup 33
- Setting Description 34
- Port Stop Bits 36
- SmartPad II Setup 38
- Display Brightness 39
- System Setup 41
- Language 43
- SmartPad II Tools 46
- Receiver Status 47
- GPS Logger 48
- Figure 2-27: Lightbar Test 49
- Delete Files 50
- Set Date and Time 51
- Chapter 2 Notes 53
- Guidance Setup 57
- Time Start Up 58
- Swath Width 59
- Look Ahead 60
- Direction to Swath 61
- Distance to Swath 62
- Status Detect 63
- GPS Type 65
- GPS Data Rate 66
- As Applied 69
- Map Object 71
- Data Examples 72
- Time Start up 79
- Drive Sensitivity 81
- Display Mode 82
- Parallel MSG 1 84
- Parallel MSG 2 85
- Parallel MSG 3 86
- Curved MSG 87
- Hazard Range 91
- Starting Real-Time Guidance 92
- SmartPad II View Page Buttons 94
- Figure 3-51: Solid View 95
- Figure 3-52: Spray Boom View 95
- Figure 3-53: Zoom Pan Mode 96
- Figure 3-54: North Up View 97
- Figure 3-55: COG View 97
- Guidance Application Modes 98
- The Parallel Guidance Mode 99
- Mark Point B 100
- Turning On Applied Swath 101
- Exiting Real-Time Guidance 101
- The Curved A-B Guidance Mode 102
- The Curved Guidance Mode 104
- SmartPad II 106
- Software Version 4.02 106
- Marking Point A 109
- Marking Point B 110
- Circle Guideline Guidance 110
- Applied Area Detection 116
- Detecting Neighboring Swath 117
- Creating a Field Boundary 118
- Mapping Points and Hazards 121
- Marking a Named Point 122
- Marking a Hazard 123
- Marking a Named Hazard 124
- Hazard Detection 125
- Lightbar Index 127
- Lightbar State Description 128
- Chapter 3 Notes 130
- Lightbar Setup 135
- Use Lightbar 136
- LED Brightness 137
- Alarm Range 139
- Display Message 140
- Antenna Setup 141
- Setting Name Default Value 142
- Change at 1st 142
- Time start Up 142
- Offset Direction 143
- Offset Distance 144
- Data Setup 145
- Point/Grid File 147
- Boundary 148
- Background 149
- Sample Number 150
- Sample Name 151
- The Real-Time View Page 154
- Real-Time View Options 156
- Mapping a Field Boundary 157
- Dropping a Sample Point 160
- Navigating to Points 163
- Editing a Sample Point 167
- Deleting a Sample Point 168
- Chapter 4 Notes 172
- Chapter 5 - Field Mapping 173
- About the Mapper Application 174
- Fieldware for Smartpad II 184
- Real-Time View Buttons 186
- Mapper Application Modes 192
- The Polygon Stream Mode 193
- The Polygon Mark Mode 194
- The Polyline Stream Mode 195
- The Polyline Mark Mode 196
- Chapter 5 Notes 197
Powiązane produkty i podręczniki dla Komputery Teejet GuideLine SmartPad II
Komputery Teejet RMS Office Instrukcja Użytkownika
(120 strony)
(120 strony)
Komputery Teejet RX370p Instrukcja Użytkownika
(24 strony)
(24 strony)
Komputery Teejet RX 400p Instrukcja Użytkownika
(151 strony)
(151 strony)
(10 strony)
Komputery Teejet LH 500 Instrukcja Użytkownika
(16 strony)
(16 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji