Teejet Matrix 840G User Manual Instrukcja Użytkownika Strona 21
- Strona / 67
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
●
16
GPS Port
GPS Port sets port transmission to Internal or External.
1. Press GPS ICON .
2. Press GPS PORT ICON .
3. Select
►Internal – use the internal (D)GPS (if equipped) and transmit
out
►External – receive external (D)GPS data
4. Press
►PAGE RIGHT ARROW to proceed to GPS Status.
►SYSTEM SETUP TAB to return to main System Setup
screen.
NOTE: This setting is required for FieldPilot and Tilt Sensor
Operation, as well as proper BoomPilot operation.
Figure 2-17: GPS Port
NOTE: Working with GPS signals such as Omnistar HP/XP or RTK
will require GPS port to be set to External.
External Receiver Minimum Confi guration Requirements
Before the Matrix will connect and work with an external GPS
receiver, these minimum confi guration requirements must be met.
Serial Port Settings
Baud rate: 19,200
Data Bits: 8
Parity: None
Stop Bits: 1
Serial Port connection requirements
Male 9 pin RS-232 serial cable
NOTE: May require Null modem adapter depending on pin out of
receiver.
NMEA Strings
GGA 5 Hz
VTG 5 Hz
ZDA 0.2 Hz
GPS Status
GPS Status displays information regarding data rates, number of
satellites in view, and satellite quality and ID.
1. Press GPS ICON .
2. Press GPS PORT ICON to view data including:
◄GGA/VTG (Data Rates) – the number of GPS positions per
second.
◄Num Sats – the number of GPS satellites in view (minimum of
4 are required for DGPS)
◄HDOP – a measure of satellite geometry strength in the
horizontal plane. A HDOP value of less than 2 is preferred.
◄PRN – the current DGPS satellite ID. (see PRN chart)
◄GGA Quality – the current quality indicator of the GPS signal.
(see GGA chart)
3. Press
►CHECKERED FLAG to complete GPS Setup.
►SYSTEM SETUP TAB to return to main System Setup
screen.
NOTE: If GPS is not available, all entries will be “Invalid”
Figure 2-18: GPS Status
- U s E R M A N U A L 1
- Table of Contents 2
- CHAPTER 1– PRODUCT OVERVIEW 6
- SYSTEM FEATURES 6
- SYSTEM COMPONENTS 6
- Matrix 570G Console 6
- RealView Camera 7
- Matrix 840G Console 7
- Video Selector Modules 8
- GPS Antennas 8
- Configurations 10
- Engage/Disengage 11
- Power on/off 12
- Start Up Sequence 13
- GENERAL OPERATION INFORMATION 13
- 98-05188 R2www.teejet.com 14
- Page Layout and Navigation 15
- Home Menu 16
- CHAPTER 2 – UNIT SETUP 16
- SYSTEM SETUP 17
- Lightbar 17
- Display Mode 18
- LED Brightness 18
- Language 19
- Time Zone 20
- GPS Type 20
- GPS Port 21
- GPS Status 21
- GGA Requirements 22
- TSLIB calibration utility 23
- Touch crosshair to calibrate 23
- Screenshot 24
- Enable/Disable 24
- Capture an Image 25
- About/Save 25
- Save About Information 25
- Eight Channel VSM 26
- BOOMPILOT/SINGLE BOOM SETUP 27
- BoomPilot Setup 27
- Delay On 28
- Delay Off 29
- Number of Boom Sections 29
- Boom Section Width 29
- Single Boom Setup 30
- VEHICLE SETUP 30
- Vehicle Type 31
- Antenna Height 31
- Direction to Boom 31
- TILT GYRO MODULE SETUP 32
- Level Tilt Position 1 33
- Level Tilt Position 2 33
- Tilt Calibration Complete 33
- Tilt Correction Off 33
- FIELDPILOT SETUP 34
- Autosteer 34
- Valve Setup 35
- Cycle Left 36
- Cycle Right 36
- Maximum Duty Cycle 36
- Valve Test 37
- Con gure FieldPilot 37
- Coarse Steering Adjustment 38
- Fine Steering Adjustment 38
- Deadband 39
- Lookahead 39
- CHAPTER 3 – GUIDANCE 40
- GUIDANCE OPERATION MODES 40
- Straight A-B Guidance 40
- Curved A-B Guidance 40
- Circle Pivot Guidance 40
- Last Pass Guidance 41
- GUIDANCE BAR & STATUS BAR 41
- Guidance Bar 41
- Status Bar 41
- 0.5314.6 42
- Vehicle View 43
- Guidance Mode Select 43
- Marking A and B Points 45
- Activate Last Pass Guidance 45
- Last Pass 45
- Create Field Boundary 45
- Zoom In/Out & Perspective 47
- BoomPilot 47
- Return to Point 49
- Zoom In/Out 50
- World View 50
- Pan Mode 50
- Guidance Over Video 52
- Steering Angle Indicator 53
- Single Camera Selection 53
- Four Channel VSM 54
- Split Camera View 55
- Guideline Adjustment 56
- CHAPTER 4 – MONITORING 57
- JOB VIEW 57
- Job Information 57
- Save Information 57
- PDF Report 58
- KML Data 58
- BOOM MONITORING 59
- Boom Monitor 59
- Menu Options 61
- Unit Setup 61
- CHAPTER 5 – APPENDIX 61
- APPENDIX A ICON REFERENCE 61
- BoomPilot/Single Boom Setup 62
- Vehicle Setup 62
- Tilt Gyro Module Setup 62
- FieldPilot Setup 62
- Commandes générales 62
- Guidance Screens 63
- Job View 64
- APPENDIX B TIME ZONES 64
Powiązane produkty i podręczniki dla Komputery Teejet Matrix 840G User Manual
(58 strony)
(2 strony)
(2 strony)
(2 strony)
(2 strony)
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji