Teejet Matrix 840G User Manual Instrukcja Użytkownika Strona 25
- Strona / 58
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
www.teejet.com
36
●
98-05141 R2
37
●
NOTE: BoomPilot settings are only visible and
necessary if a SmartCable or SDM is
present. If neither is present, see Single
Boom Setup section.
Figure 2-38: Boom Section Setup (SDM detected)
Overlap
Overlap determines the amount of overlap allowed
when the boom sections are turned on and off using
BoomPilot.
1. Press OVERLAP ICON .
2. Press UP/DOWN ARROW ICONS to
change between:
►0%
►50%
►100%
3. Press
►PAGE RIGHT ARROW to proceed to Delay
On.
►BOOMPILOT/SINGLE BOOM SETUP TAB
to return to main Boom Section Setup screen.
Figure 2-39: Overlap
Figure 2-40: Examples of Overlap
100%
50%
0%
Figure 2-36: Video w/Four Channel VSM
Figure 2-37: Camera Configuration
BOOMPILOT/SINGLE
BOOM SETUP
BoomPilot Setup is used to confi gure
Overlap, Delay On, Delay Off, Number of Boom
Sections, and Boom Section Width settings.
Single Boom Setup is available when a SmartCable
or Section Driver Module (SDM) is not present.
Confi gurations for Overlap, Delay On, Delay Off,
Number of Boom Sections will not be available, and
only one boom section width can be entered.
BoomPilot Setup
If a SmartCable or Section Driver Module (SDM)
is present, up to 15 boom section widths can be
entered.
1. Select UNIT SETUP from Home Menu .
2. Press BOOMPILOT/SINGLE BOOM SETUP
TAB
3. Select from:
►Overlap – determines the amount of
overlap allowed
►Delay On – establishes the timing for the
boom section valves to switch on
►Delay Off – establishes the timing for the
boom section valves to switch off
►Number of Boom Sections
#
– establishes
the number of available boom sections
►Boom Section Width – establishes the
width of each boom section
OR
Press PAGE RIGHT ARROW to cycle through
all settings.
NOTE: Options labels are current settings. While in
a setting screen, press icon to view available
factory settings and setting ranges.
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Powiązane produkty i podręczniki dla Komputery Teejet Matrix 840G User Manual
(2 strony)
(2 strony)
(2 strony)
(2 strony)
(2 strony)
(127 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji