Teejet Matrix 840G User Manual Instrukcja Użytkownika Strona 42
- Strona / 58
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
www.teejet.com
68
●
98-05141 R2
69
●
Field View
To access the Field View screen.
1. Press HOME BUTTON or press the screen
to activate the icons and select HOME ICON
in bottom left corner of screen.
2. Select FIELD VIEW from Home Menu .
Figure 3-34: Home Menu - Field View
Swath acres
0.00
0.0
Field Boundary
Field boundaries establish application area and
determine the no apply zone.
NOTE: A Field Boundary can be created in either
Last Pass Guidance while in Vehicle View or
during any guidance while in Field View.
To create a fi eld boundary:
1. Drive to a desired location at the perimeter of the
fi eld/area.
2. While the vehicle is in motion, press
BOUNDARY ICON .
3. Travel the perimeter of the fi eld/area.
4. Finish boundary:
►Travel to within a swath width of the starting
point. The boundary will close automatically (the
white guideline will turn black).
►Press BOUNDARY FINISH ICON . A
straight line will complete the boundary between
your current location and the starting point.
NOTE: If a swath was applied while creating a
boundary, the boundary line will be to the
exterior of the applied swath.
NOTE: The BOUNDARY FINISH ICON
is not
available for selection (grayed out) until the
minimum distance is traveled (five-times the
swath width).
Use CANCEL BOUNDARY ICON to cancel
the new fi eld boundary process and revert to the
previous boundary (when established).
Figure 3-35: Boundary in Progress
mph acres
2.7512.3
Figure 3-36: Boundary Established
mph acres
4.9212.4
Figure 3-33: Overview of Field View
On Screen Guidance
• Guidelines
►Orange – active guidance line
►Black – boundary line
• Points - markers for established points
►Red Point – Return to Point
►Blue Point – Mark A
►Green Point – Mark B
• Coverage Area – illustrates applied area and
overlap:
►Blue – one application
►Red – two or more applications
• Zoom In/Out – adjust the map’s visible area.
Button Assistance
• Zoom In/Out & Perspective – adjust the map’s
visible area.
FIELD VIEW
Field View creates a computer-generated image of the vehicle position and application area from
an aerial perspective. From this screen one can access options for boundary areas and a marked
point or enter World View and Pan modes.
mph acres
0.5314.6
5.8
Guidance Bar
Field View
(Zoom In/Out)
or can use Zoom In/Out
Buttons
Vehicle Representation
Pan Mode
World View
Status BarNavigation Guidelines
Mark Boundary
Finish Boundary
Mark Point
Return to Point
Cancel Boundary
Cancel Point
Home/Menu Options
or press Home Button
Painted Coverage Area
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Powiązane produkty i podręczniki dla Komputery Teejet Matrix 840G User Manual
(2 strony)
(2 strony)
(2 strony)
(2 strony)
(2 strony)
(127 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji